PIC16F737-I/SP【PDF 202/231 页】IC PIC MCU FLASH 4KX14 28DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3841

198页 199页 200页 201页 [202页]203页 204页 205页 206页

2004 Microchip Technology Inc.

DS30498C-page 33

PIC16F7X7

4.0

OSCILLATOR

CONFIGURATIONS

4.1

Oscillator Types

The PIC16F7X7 can be operated in eight different oscil-

lator modes. The user can program three configuration

bits (FOSC2:FOSC0) to select one of these eight modes

(modes 5-8 are new PIC16 oscillator configurations):

Low-Power Crystal

Crystal/Resonator

High-Speed Crystal/Resonator

External Resistor/Capacitor with

FOSC/4 output on RA6

RCIO

External Resistor/Capacitor with

I/O on RA6

INTIO1 Internal Oscillator with FOSC/4

output on RA6 and I/O on RA7

INTIO2 Internal Oscillator with I/O on RA6

and RA7

ECIO

External Clock with I/O on RA6

4.2

Crystal Oscillator/Ceramic

Resonators

In XT, LP or HS modes, a crystal or ceramic resonator

is connected to the OSC1/CLKI and OSC2/CLKO pins

to establish oscillation (see Figure 4-1 and Figure 4-2).

The PIC16F7X7 oscillator design requires the use of a

parallel cut crystal. Use of a series cut crystal may give

frequency

out

the

crystal

manufacturer’s

specifications.

FIGURE 4-1:

CRYSTAL OPERATION

(HS, XT OR LP OSC

CONFIGURATION)

TABLE 4-1:

CAPACITOR SELECTION FOR

CRYSTAL OSCILLATOR (FOR

DESIGN GUIDANCE ONLY)

Note 1:

See Table 4-1 for typical values of C1 and C2.

2: A series resistor (RS) may be required for AT

strip cut crystals.

3: RF varies with the crystal chosen (typically

between 2 M

to 10 M).

C1(1)

C2(1)

XTAL

OSC2

RS(2)

OSC1

RF(3)

Sleep

To Internal

Logic

PIC16F7X7

Osc Type

Crystal

Freq

Typical Capacitor Values

Tested:

32 kHz

33 pF

200 kHz

15 pF

200 kHz

56 pF

1 MHz

15 pF

4 MHz

15 pF

4 MHz

15 pF

8 MHz

15 pF

20 MHz

15 pF

Capacitor values are for design guidance only.

These capacitors were tested with the crystals listed

below for basic start-up and operation. These values

were not optimized.

Different capacitor values may be required to produce

acceptable oscillator operation. The user should test

the performance of the oscillator over the expected

VDD and temperature range for the application.

See the notes following this table for additional

information.

Note 1: Higher capacitance increases the stability

of oscillator but also increases the

start-up time.

2: Since each crystal has its own character-

istics, the user should consult the crystal

manufacturer for appropriate values of

external components.

3: Rs may be required in HS mode, as well

as XT mode, to avoid overdriving crystals

with low drive level specification.

4: Always verify oscillator performance over

the VDD and temperature range that is

expected for the application.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式